Sharp Cooktop Cooktop bruksanvisning

Användarhandboken för enheten Sharp Cooktop Cooktop

Sharp Cooktop Cooktop bruksanvisning

Extrakt av innehållet

Innehåll sammanfattning på sidan nej. 1

SPECIAL WARNINGINSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICALINSPECTOR’S USE.READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.CLEARANCES & DIMENSIONSFor SAFETY CONSIDERATIONS do not install a appliance in any combustible cabinetry which is notin accord with the stated clearances and dimensions on page 2. See Figures 1 and 2.APPLIANCE MEASUREMENTS .................................2CHECKING INSTALLATION......

Innehåll sammanfattning på sidan nej. 2

INSTALLATION MANUALAPPLIANCE MEASUREMENTSCLEARANCES AND DIMENSIONS• Provide adequate clearances between the appliance and adjacentcombustible surfaces.31 1/2" glass andcontrol panel29 7/8"width of unit15"autodrawer open15 5/8" fromthe bottom sideof the cooktopto thebottom cover23 7/16"depth• Contact surface must be solid and level. Pay special attentionto the countertop. Be sure it is solid enough for the weight ofthe appliance.30"door andlouver width1 11/16"door thickness• Dimensions that

Innehåll sammanfattning på sidan nej. 3

INSTALLATION MANUALIMPORTANT NOTES TO THE INSTALLERIMPORTANT SAFETY INSTRUCTIONS• Read all of the Installation Manual before installing theappliance.• Remove all packing material from the drawer and cooktopbefore connecting the electrical supply to the appliance.• Observe all governing codes and ordinances.• Be sure to leave these instructions with the consumer.If the information in this manual is not followedexactly, a fire or electrical shock may result causingproperty damage, persona

Innehåll sammanfattning på sidan nej. 4

INSTALLATION MANUALB ADJUSTING ANTI-TIP BRACKETINSTALLATIONMeasure the thickness of the counter. See Figure 7. Locate theAnti-Tip Bracket on the backside of the appliance. See Figure 8.Loosen screws and adjust space between the glass cooktop andbracket to match the counter thickness plus 1/16”. See Figure 9.Tighten the screws to secure the bracket at the correct counter heightdimension.• Review and plan ahead all safety instructions, cabinetclearances and dimensions, power supply placement a

Innehåll sammanfattning på sidan nej. 5

INSTALLATION MANUALC INSTALL THE STOP SCREWSFPUSH THE UNIT BACK UNTIL IT HITS THE STOPSCREWS INSTALLED IN STEP “C” See Figure 12.IMPORTANT Confirm all cut-out openings and clearances asindicated on page 2 before installing the appliance. These twostop screws prevent the appliance from sliding out of position duringoperation. Attach the stop screws (supplied in the screw bag) to theright and left sides of the cabinet opening as specified. See Figure10. Use a 1/16” drill bit to pre-drill h

Innehåll sammanfattning på sidan nej. 6

INSTALLATION MANUALNational Electrical Codes, ANSI/NFPA No. 70-Latest Edition.I MAKE SURE THE EDGE OF THE COUNTERTOP FITSEffective January 1, 1996, the national Electrical Code requires thatnew, but not existing, construction utilize a four-conductor connection for this appliance class. When installing this appliance in newconstruction, a mobile home, recreational vehicle or an area wherelocal codes prohibit grounding through the neutral conductor, followthe instructions in the section on NEW CO

Innehåll sammanfattning på sidan nej. 7

INSTALLATION MANUALPOWER CONNECTIONS3-WIRE CONNECTIONWhen local codes permit connecting the cabinet-grounding conductor to the neutral (white) wire.This appliance is manufactured with a neutral (white) power supplywire and a cabinet-connected green grounding wire.1 Disconnect the power supply.Connect the appliance cable to the junction box through the ULlisted conduit connector. Complete electrical connection accordingto local codes and ordinances. For preferred junction box location,see Figure

Innehåll sammanfattning på sidan nej. 8

INSTALLATION MANUALMODEL AND SERIAL NUMBER LOCATIONBEFORE YOU CALL FOR SERVICEThe Rating Plate, including model and serial number, is located onthe faceplate behind the Microwave Drawer front.Read the BEFORE YOU CALL and operating instruction sectionsin your Operation Manual. It may save you time and expense. Thelist includes common occurrences that are not the result of defectiveworkmanship or materials in this appliance.CARE, CLEANING AND MAINTENANCERefer to the warranty in your Operation Manu

LÄMNA EN KOMMENTAR